| Author |
|
rboyleiii
Newbie
Joined: January 15 2008
Location: United States
Online Status: Offline
Posts: 11
|
| Posted: May 29 2008 at 21:10 | IP Logged
|
|
|
In PH you can go to Help, About, and controllers and it will list the firmware version of the PLM.
By the response you posted, it looks like firmware version is 63
S: 0x02 0x60 0x60 Get IM Info
R: 0x02 0x60
<ID high byte> <ID middle byte> <ID low byte>
<Device Category> <Device Subcategory> < Firmware Revision>
<0x06>
HTH
|
| Back to Top |
|
| |
TonyNo
Moderator Group
Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
|
| Posted: May 30 2008 at 07:23 | IP Logged
|
|
|
LOL I knew that. Don't know why I didn't do it, though! Thanks.
|
| Back to Top |
|
| |
TonyNo
Moderator Group
Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
|
| Posted: June 04 2008 at 21:24 | IP Logged
|
|
|
New PLM installed. Still 63, so, we'll soon see.
|
| Back to Top |
|
| |
BeachBum
Super User
Joined: April 11 2007
Location: United States
Online Status: Offline
Posts: 1880
|
| Posted: June 04 2008 at 21:38 | IP Logged
|
|
|
I went about 3 weeks with mine before I had a failure then they happened frequently. Am still on the road so it will be awhile before I contact SH.
__________________
Pete - X10 Oldie
|
| Back to Top |
|
| |
TonyNo
Moderator Group
Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
|
| Posted: June 06 2008 at 19:39 | IP Logged
|
|
|
Grr. PLM #2 locked. As before, the last command sent was X10.
Edited by TonyNo - June 06 2008 at 19:39
|
| Back to Top |
|
| |
BeachBum
Super User
Joined: April 11 2007
Location: United States
Online Status: Offline
Posts: 1880
|
| Posted: June 06 2008 at 21:11 | IP Logged
|
|
|
I rest my case.... 
__________________
Pete - X10 Oldie
|
| Back to Top |
|
| |
TonyNo
Moderator Group
Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
|
| Posted: June 06 2008 at 22:17 | IP Logged
|
|
|
For the record, the new PLM is v2.8 (previous one was 2.75).
|
| Back to Top |
|
| |
TonyNo
Moderator Group
Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
|
| Posted: June 13 2008 at 07:24 | IP Logged
|
|
|
I had two lockups last night. Hunting possible sequences that lead to failure.
I did notice that when it's locked, ph_getinsteonlevelrt seems to hang. If it does time out, I didn't wait long enough to see it.
|
| Back to Top |
|
| |
BeachBum
Super User
Joined: April 11 2007
Location: United States
Online Status: Offline
Posts: 1880
|
| Posted: June 13 2008 at 09:13 | IP Logged
|
|
|
Tony, as I remember when mine locked up ph_getinsteonlevelrt, which I use for error recovery, was running and when I had a failure it runs up to 5 times. It looped for 5 times on all my Insteon devices so it does appear to time out.
I wonder what you and I are doing that others are not. Still on the road so when I get back next week no telling what the house lights will look like.
__________________
Pete - X10 Oldie
|
| Back to Top |
|
| |
TonyNo
Moderator Group
Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
|
| Posted: June 14 2008 at 00:19 | IP Logged
|
|
|
Another few lockups, all after my X10 sink light was turned on/off. Swapped it with a spare Insteon LampLinc. Watching for the next offender... 
|
| Back to Top |
|
| |
TonyNo
Moderator Group
Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
|
| Posted: June 18 2008 at 07:31 | IP Logged
|
|
|
Grr. Last night, I had another lockup with the last good transmission being X10. Something was setting off a motion detector in the basement, and I have an appliance module that controls a fluorescent fixture down there.
|
| Back to Top |
|
| |
BeachBum
Super User
Joined: April 11 2007
Location: United States
Online Status: Offline
Posts: 1880
|
| Posted: June 18 2008 at 10:40 | IP Logged
|
|
|
I had no failures  while I was gone for 4 weeks but the appliance module I have a TV on did not have a load on it as the TV was turned off. This is also the module I was having a lookup with. I’m back to regular operation now and will try and trap it when it occurs.
__________________
Pete - X10 Oldie
|
| Back to Top |
|
| |
Active Topics 
Memberlist 
Search 
Help
Register 
Login
PowerHome Messageboard : PowerHome Programming
Topic: Insteon Device Change Trigger Problem
